Jump to content

Variation & Optimization

Anything related to manual/automated design creation and variant management.

116 topics in this forum

  1. Batch Mode

    By Jörg,   
    • 11 replies
    • 19664 views

  2. 50K MR Tanker

    By Daehwan Park,   
    • 2 replies
    • 4508 views

  3. About .foam file

    By Mr. Wilson Wang,
    • 1 reply
    • 4269 views

  4. Adding new parameters to an existing results table

    By Mr. Carsten Fuetterer,   
    • 0 replies
    • 2896 views

  5. Adjoint CFD

    By Mr. Kim Moo Sung,   
    • 4 replies
    • 3639 views

  6. Batch Mode Runs

    By yuvraj,
    • 2 replies
    • 1145 views

  7. Beam in bending

    By Stefan Harries,   
    • 1 reply
    • 3802 views

  8. Black Box Optimization Problem

    By Matthias Maasch,
    • 1 reply
    • 3915 views

  9. Bow Transformation of a Ship Hull with Lackenby: Step by Step

    By Mr. Cillian McGreer,   
    • 4 replies
    • 4278 views

  10. Bulb Deformation using Delta Shift and Surface Delta Shift

    By Mr. Carlo Pasquinucci,   
    • 0 replies
    • 4664 views

  11. CAESES 4.4.1 and Dakota

    By Mr. hamid reza,
    • 4 replies
    • 2919 views

  12. CAESES and workbench use Fluent to optimize the design and cause failure

    By sisi,   
    • 6 replies
    • 1508 views

  13. CAESES Batch Mode: Guidance Needed for DOE and Optimization Setup

    By djusng,   
    • 1 reply
    • 917 views

  14. CAESES input and response surface visualization

    By MIHCool,
    • 13 replies
    • 3439 views

  15. Can we add extra design variants on top of the existing design variants?

    By Mr. Joseph Jhun,   
    • 4 replies
    • 2997 views

  16. Chart Colouring

    By CJ Coll,
    • 2 replies
    • 1230 views

  17. Check Validity result

    By Ms. Kerstin Lorry,   
    • 8 replies
    • 4210 views

  18. Command in Caeses Software especially for Marine Application

    By Atiyah,
    • 1 reply
    • 1861 views

  19. Constant volume kept during DAKOTA-Optimization

    By Mr. hjkl 3ff,   
    • 8 replies
    • 5340 views

  20. Cookbook : Offset Extraction

    By Mr. Daehwan Park,
    • 0 replies
    • 2531 views

  21. Cookbook : Partially parametric hullform variation

    By Mr. Daehwan Park,
    • 0 replies
    • 2500 views

  22. Coupling Friendship to HEEDS?

    By Mr. Henrik Philipsen,   
    • 12 replies
    • 5604 views

  23. Create Geometry in Batch-Mode

    By CHenk,
    • 6 replies
    • 1825 views

  24. Creating Sections after Lackenby Transformation fails

    By Guest Ms. Fleur Bakkum,
    • 4 replies
    • 2847 views

  25. Dakota incremental LHS function

    By Mr. Alexandros Priftis,   
    • 8 replies
    • 4692 views
×
×
  • Create New...