Jump to content

Search the Community

Showing results for tags 'hull design'.

The search index is currently processing. Current results may not be complete.


More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • CAESESĀ®
    • General Modeling
    • Software Connections
    • Variation & Optimization
    • Post-Processing
    • Feature Programming
    • Installation
    • Miscellaneous
    • Ideas and Suggestions
    • FAQ

Categories

  • Articles
    • Forum Integration
    • Frontpage
  • Pages
  • Miscellaneous
    • Databases
    • Templates
    • Media

Categories

  • New Features
  • Other

Blogs

  • Mr. Arne Bergmann's Blog
  • FSYS DAEHWAN PARK
  • Mr. Arne Bergmann's Blog
  • Rel 3.1
  • Joerg Palluch's Blog

Calendars

  • Community Calendar

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 5 results

  1. Dear all, I'm having some issues trimming the Brep or Surface either with curves, surfaces or Breps. My intention is to parametrize the end of the Brep or Surface in order to end at the transom (x=0) of the hull, while at the same it follows the step. I manage only to trim the surface (04_UpperSectionSurface) first on the principal plane (X=0) first and then trim the Brep (06_Step|Upper_Section_Brep) on the step geometry, however this ends with some discrepancies on the final Brep, due to the initial trimming of the 04_UpperSectionSurface. I'm attaching a few screenshots of the area, while also the model. Could you please advise upon the matter? Thanks a lot. Best regards, George TestSWAN_v2.cdbc
  2. I have been researching Caeses and how it can be used in vessel optimisation. One video I came across that was very useful was the 'Optimization of a Double-Ended Ferry with CAESES and CADMATIC'. In this video, it quickly runs through how the vessel optimisation was set up. I am currently undergoing my 4th-year dissertation and would like to conduct research on the 'Optimisation of small fishing vessel hulls to maximise deck space and minimise operational costs'. I have not used Caeses much in the past and consider myself to be inexperienced with the software. My question is; Is there any recommendations of articles to read so that I can set up a small fishing vessel hull optimisation simulation? Or any guidance to help me through my studies? I am not very sure how to; start setting up my model geometry, set constraints, begin optimisation etc Any comments are much appreciated
  3. Dear all, Currently working on a fast monohull parametric design and I'm in the process of adding some spray rails to the hull, as the images attached below. I'd like to ask if their is any efficient way to parametrize such geometry at the hull surface and/or if anyone had worked on a similar project and maybe could share some details and insights on the topic? Attached you may find my project while also some photos of spray rails geometries Thank you in advance for your time. Best regards, George TestSWAN_v2.cdbc
  4. Dear all, I'm having some issues trimming the Brep or Surface either with curves, surfaces or Breps. My intention is to parametrize the end of the Brep or Surface in order to end at the transom (x=0) of the hull. I'm attaching a few screenshots of the area, while also the model. Could you please advise upon the matter? Thanks a lot. Best regards, George TestSWAN_v2.cdbc
  5. Hi! I'm wondering whether it's possible to insert a quad/plane textured with image? Also, image contains coordinate system which I would like to calibrate to Caeses units and then I would draw curves snapped on that plane over the image. I'd actually like to draw a ship hull from its lines drawing, and then loft or whatever to recover the full shape. J.Basic
×
×
  • Create New...